News
Statistics
| Number of Journals | 34 |
| Number of Issues | 1,306 |
| Number of Articles | 9,427 |
| Article View | 9,189,270 |
| PDF Download | 5,621,868 |
Empirical Analysis of Fracture in Polymeric Unidirectional Composites With mechanical connections | ||
| دوفصلنامه مهندسی شناورهای تندرو | ||
| Volume 22, Issue 62, August 2023, Pages 13-23 PDF (1.21 M) | ||
| Document Type: Original Article | ||
| Authors | ||
| Mohammadhusein Qaedsharaf* 1; mohammadmahdi attar2; Ehsan Yari3; vahid aeeni4 | ||
| 1Maut | ||
| 2Department of Mechanical Engineering, Islamic Azad University, Hamedan Branch, | ||
| 3Assistant Professor, Department of Mechanical Engineering, Malik Ashtar University of Technology, Isfahan | ||
| 4Instructor of Males' No. 1 Technical and Vocational University (Shahid Mofatteh Hamedan) | ||
| Receive Date: 09 May 2023, Revise Date: 31 May 2023, Accept Date: 26 June 2023 | ||
| Abstract | ||
| Composites are a class of advanced materials in which simple material combinations are used to create new materials with superior mechanical and physical properties. The use of composites in vessels has several advantages such as weight loss, improvement of radar and magnetic properties, resistance to chemical corrosion and mechanical corrosion and fatigue, vibration absorption and noise, high strength-to-weight ratio, good resistance to underwater shocks. Replacing steel components with composite components can save 60 to 80 percent on component weight and 20 to 50 percent weight savings by replacing aluminum and composite components. In this study, the pin joints used in marine composite equipment were investigated in multilayer monodirectional composite made of glass and epoxy fibers. For this purpose, a model was considered for the problem and the parameters of the center of the pin from the free edge of the multilayer to the pin diameter (w/d) and the ratio of multilayer width to pin diameter (e/d) were defined as the variables of the problem. Then, to obtain the rupture force and rupture mode, the samples were subjected to tensile loading. The results showed that the maximum force tolerance and rupture mode were significantly affected by w/d and e/d parameters and with increasing the w/d ratio, the force tolerant increased and the mode of the rupture changed from shear to the mode of shear to the crush mode, and for each e/d ratio, there is an optimal limit for w/d. | ||
| Keywords | ||
| Composite; floating; glass fiber; epoxy; rupture; stretching; cutting; crush | ||
| References | ||
|
[1] Attar, Mohammad Mahdi. Barati, Farzan. Ahmadpour, Mahdi. Rezapour, Ehsan. (2016). Failure analysis of unidirectional polymeric matrix composites with two serial pin loaded-holes. journal of mechanical science and technology, 30, pp.2583–2591.##[2] Tao, Wu. Kaifu, Zhang. Hui, Cheng. (2016). Analytical modeling for stress distribution around interference fit holes on pinned composite plates under tensile load. S1359-8368 (16) 30907-6.##[3] Gamdani, Farid. Boukhili, Rachid. Vadean, Aurelian. (2015). Tensile strength of open-hole, pin-loaded and multi-bolted single-lap joints in woven composite plates. Materials and Design, 88, 702–712.##[4] Wang, W. Rans, C. Alderliesten, R.C. Benedictus, R. (2015). Predicting the influence of discretely notched layers on fatigue crack growth in fibre metal laminates. Engineering Fracture Mechanics, Volume 145, Pages 1-14.##[5] Moure, M. M. Otero, F. García-Castillo, S. K. Sánchez-Sáez, S. Barbero, E. Barbero, E. J. (2015). damage evolution in open-hole laminated composite plates subjeted to in-plane loads. Composite Structures, Volume 133, 1, Pages 1048-1057.##[6] Damith, Mohotti. Tuan, Ngo, Sudharshan, N. Raman. Muneeb, Ali. Priyan, Mendis. (2014). Plastic deformation of polyurea coated composite aluminium plates subjected to low velocity impact. Materials & Design, Volume 56, Pages 696-713.##[7] Grekov, Mikhail. Morozov, Nikita. Yazovskaya, Anna. (2014). Effect of surface stress on strength of a plate with elliptical and triangular nanoscale holes. 20th European Conference on Fracture (ECF20)##[8] Vinayak, B.G. Jayaprakash, K. Naik, N.K. (2012). Fatigue behavior of laminated composites with a circular hole under in-plane uniaxial random loading. Materials & Design, Volume 40, Pages 245-256.##[9] Fadil, Ibrahim, Soykok. Sayman, Onur. Pasinli, Ahmet. (2013). Effects of hot water aging on failure behavior of mechanically fastened glass fiber/epoxy composite joints. composite, 54, pp.59-70.##[10] Darwish, Feras. Tashtoush, Ghassan. Gharaibeh, Mohammad. (2012). Stress concentration analysis for countersunk rivet holes in orthotropic plates. European Journal of Mechanics A/Solids, 37, 69-78.##[11] Gurbet, örcen. Mustafa, Gür and. Mustafa, özen. (2012). Seawater effect on pin-loaded laminated composites with two parallel holes. Journal of Mechanical Science and Technology, 26 (12), pp. 4055-4063.##[12] Camanho, P. P. Melro, A. R. Andrade Pires, F. M. Pinho, S. T. Micromechanical analysis of polymer composites reinforced by unidirectional fibres: Part II – Micromechanical analyses. International Journal of Solids and Structures, Volume 50, Issues 11–12, p. 1906–1915, 2013.##[13] Nazari, Ali. Didehvar, Neda. (2011). Analytical modeling impact resistance of aluminum epoxy laminated composites. Composites Part B: Engineering, Volume 42, Issue 7, Pages 1912-1919.##[14] کاربرد آلومینیوم و مواد کامپوزیتی در شناورها، محمد فارسی، داوود پورشمس، عباس دشتی منش، مصباح سایبانی، نهمین همایش صنایع دریایی | ||
|
Statistics Article View: 92 PDF Download: 97 |
||