News

 Statistics

Number of Journals34
Number of Issues1,306
Number of Articles9,427
Article View9,188,291
PDF Download5,620,733
hoseini baghdad abadi, M., zirak, S., rajabi zargar abadi, M. (2019). Numerical Study of the Effect of Rotation on the Film Cooling Effectiveness of a Turbine Blade with Square Pulsating Cooling Flow. Electronic and Cyber Defense, 8(1), 113-130.
mahdi hoseini baghdad abadi; saAdat zirak; mehran rajabi zargar abadi. "Numerical Study of the Effect of Rotation on the Film Cooling Effectiveness of a Turbine Blade with Square Pulsating Cooling Flow". Electronic and Cyber Defense, 8, 1, 2019, 113-130.
hoseini baghdad abadi, M., zirak, S., rajabi zargar abadi, M. (2019). 'Numerical Study of the Effect of Rotation on the Film Cooling Effectiveness of a Turbine Blade with Square Pulsating Cooling Flow', Electronic and Cyber Defense, 8(1), pp. 113-130.
hoseini baghdad abadi, M., zirak, S., rajabi zargar abadi, M. Numerical Study of the Effect of Rotation on the Film Cooling Effectiveness of a Turbine Blade with Square Pulsating Cooling Flow. Electronic and Cyber Defense, 2019; 8(1): 113-130.

Numerical Study of the Effect of Rotation on the Film Cooling Effectiveness of a Turbine Blade with Square Pulsating Cooling Flow

مکانیک سیالات و آیرودینامیک
Article 9, Volume 8, Issue 1 - Serial Number 23, July 2019, Pages 113-130    PDF (1.95 M)
Document Type: Original Article
Authors
mahdi hoseini baghdad abadi; saAdat zirak* ; mehran rajabi zargar abadi
semnan
Receive Date: 11 November 2018,  Accept Date: 13 April 2019 
Abstract
In this paper, the effect of the turbine blade rotation on the temperature distribution and film cooling effectiveness for a square pulsing cooling flow is numerically studied. The square pulsed cooling air flow is injected to the turbine blade at three frequencies of 2, 50, and 500 Hz. Four rotation speeds of 0, 500, 800, and 1000 rpm, clockwise and counter-clockwise, are considered. Geometry is modeled in Gambit and the numerical analysis is performed by Fluent software. SST k-ω turbulence model is used to apply the turbulence effects. The obtained results show that the rotation deviates the coolant flow from the centerline. Changing the coolant flow to square pulsating, centerline effectiveness changes with time in a cycle. The results show that in general, the effectiveness ​​at all speeds on the pressure side are greater than the suction side. Moreover, with increasing frequency, the average level of centerline effectiveness increases.
 
Keywords
Pulse Film Cooling; Square Wave; Rotating; Turbine Blade; SST k-ω Turbulence Model
References
  1. Gao, W.J., Yue, Z.F., Li, L., Zhao, Z.N., and Tong, F.J. “Numerical Simulation on Film Cooling with  Compound Angle of Blade Leading Edge Model for Gas  Turbine”, Int. J. Heat Mass Transf., Vol. 115, No. 12, pp. 839-855, 2017.
  2. Li, Y., Zhang, Y., Su, X., and Yuan, X. “Experimental and  Numerical Investigations of Shaped  Hole Film Cooling  with the Influence of Endwall Cross Flow”, Int. J. Heat Mass Transf., Vol. 120, No. 1, pp. 42- 55, 2018.
  3. Calvin, W.E. “Turbine Cooling: USA”; US Patent 3,963,368, 1976.
  4. John, W.J. “Cooling of Aerofoil Shaped Blades: USA”; US Patent 3,620,643, 1971.
  5. Bunker, R. S. and Metzger, D.E. “Local Heat Transfer in Internally Cooled Turbine Airfoil Leading Edge Regions. Part I: Impingement Cooling without Film  Coolant Extraction”, J. Turbomach., Vol. 112, No. 3 , pp. 451–458, 1990.
  6. Bunker, R. S. and Metzger, D. E. “Local Heat Transfer  in Internally Cooled Turbine Airfoil Leading Edge Regions. Part II: Impingement Cooling with Film  Coolant Extraction”, J. Turbomach., Vol. 112, No. 3, pp.  459–466, 1990.
  7. Shin, S. and Kwak, J. S. “Effect of Hole Shape on  the Heat Transfer in a Rectangular Duct with Perforated Blockage Walls”, J. Mech. Sci. Technol., Vol. 22, No. 10, pp. 1945–1951, 2008.
  8. Wang, K., Guoqiang, X., Sun, J., and Tao, Z.  “Effect of Combined Impingement Cooling and Film  Cooling on Hybrid Cooling Effectiveness”, J. Beijing  Univ. Aeronaut. Astronaut., Vol. 34, No. 7, pp. 751–754, 2008.
  9. Wang, K., Guoqiang, X., Sun, J., and Tao, Z. “Effect of Plenum Feed Configurations on the Cooling  Effectiveness in the Hybrid Cooling Configuration”, J.  Eng. Thermophys., Vol. 29, No. 7, pp. 1185–1188, 2008.
  10. Taslim, M. E. and Pan, Y. “An Experimental Study of   Impingement on Roughened Airfoil Leading Edge Walls with Film Holes”, ASME J., Vol. 123, No. 4, pp. 767–773, 2001.
  11. Dolati, S., Amanifard, N., and Deilami, H.M. “Numerical Analysis of the Effect of Plasma Stimulator on Film Cooling Effectiveness on the Flat Plate Model”, Amirkabir J. Mech. Eng., Vol. 49, No. 3, pp. 605-616, 2016 (In Persian).
  12. Hosseini Vajargah, N., Salimi, M. R., and Taeibi Rahni, M. “Numerical Simulation of Film Cooling around the Gas Turbine Blade by Partial Averaging Method of Navier-Stokes Equations”, Amirkabir J. Mech. Eng., Vol. 48, No. 3, pp. 267-280, 2016 (In Persian).
  13. Taslim, M. E., Bakhtari, K., and Liu, H. “Experimental and Numerical Investigations of Impingement on a Rib Roughened Leading Edge  Wall”, ASME J., Vol. 125, No. 4, pp. 682– 691, 2003.
  14. Taslim, M.E. and Khanicheh, A. “Experimental and  Numerical Study of Impingement on an Airfoil Leading Edge with and  without Showerhead and Gill Film Holes”, ASME J., Vol. 128, No. 2, pp. 310–320, 2006.
  15. Taslim, M.E. and Bethka, D. “Experimental and Numerical Impingement Heat Transfer in an Airfoil Leading-Edge Cooling Channel with Cross-Flow”, ASME J., Vol. 131, No. 1, pp. 1-7, 2009.
  16. Tao, Z., Yang, X., Ding, S., Guoqiang, X., Wu, H., Deng, H., and Xiang, L. “Experimental Study of Rotation Effect on Film  Cooling over the Flat wall with a Single Hole”, Exp. Thermal Fluid  Sci., Vol. 32, No. 5, pp. 1081-1089, 2008.
  17. Moeini, A. H. and Rajabi Zargar Abadi, M. “Numerical Analysis of Film-Cooling over the Rotating Turbine Blade, Using Laterally-Diffused Hole”, Mech. Aerospace Eng. J., Vol. 14, No. 3, pp. 41-54, 2018 (In Persian).
  18. Guoqiang, X., Jianqin, Z., and Tao, Z.  “Application of the TLVA Model for Predicting Film Cooling under Rotating Frames”,  Int. J. Heat Mass Transf., Vol. 53, No. 15-16, pp. 3013-3022, 2010.
  19. Tao, Z., Zhenming, Z., Ding S., Guoqiang,  X., and  Wu, H. “Suitability of Three Different Two-Equation Turbulence Models in Predicting Film Cooling  Performance over a Rotating Blade”, Int. J. Heat Mass Trans., Vol. 52, No. 5-6,  pp. 1268-1275, 2009.
  20. Guoqiang, X., Yang, B., Tao, Z., Zhao, Z., and Wu, H. “Local Heat Transfer  Measurements on a Rotating Flat Blade Model with a Single Film Hole”, Progg. Nat. Sci., Vol. 19, No. 3, pp. 321-330, 2009.
  21. Guoqing, L., Junqiang, Z., Deng, H., Tao, Z., and  Haiwang, L. “Experimental Investigation of Rotating Film Cooling Performance in a Low Speed 1.5-Stage Turbine”, Int. J. Heat Mass Transf., Vol. 61, No. 1, pp. 18-27, 2013.
  22. Deng, H., Zhenpeng, G., Jianqin, Z., and Tao, Z. “Experiments on Impingement Heat Transfer with Film Extraction Flow on the Leading Edge of Rotating Blades”, Int. J. Heat Mass Transf., Vol. 55, No. 21-22, pp. 5425-5435, 2012.
  23. Zhaoqing, K. and Wang, J. ”Numerical Investigations of Pulsed Film Cooling on an Entire Turbine Vane”, Appl. Therm. Eng., Vol. 87, pp. 117-126, 2015.
Statistics
Article View: 479
PDF Download: 280