- [1] “AISC Load and Resistence Factor Design Specification,” American Institute of Steel Construction Inc, Chicago, 1999.##
- [2] Takahashi, Y. Takemoto, T. Takedab, and M. Takagi, “Experimental Study on Thin Steel Shear Walls and Particular Bracings under Alternative Horizental Load”, Prelim. Rep, IABSE Symp. on Resistance and Ultimate Deformability of Structures Acted on by Well Defined Repeated Loads, Lisbon, Portugal, 1973.##
- [3] Mimura and H. Akiyama, “Load-Deflection Relationship of Earthquake-Resistant Steel Shear Walls with a Developed Diagonal Tension Field”, Transactions, Architectural Institute of Japan, 1977.##
- [4] J. Thorburn, G. L. Kulak, and C. J. Montgomery, “Analysis of Steel Plate Shear Walls”, Structural Engineering Report no .107, Dept. of Civil Eng., Univ. of Alberta, Edmonton, Canada, 1983.##
- [5] A. Timler and G. L. Kulak, “Experimental Study of Steel Plate Shear Walls”, Struct. Eng. Report no. 114 , Dept. of Civil Eng., Univ. of Alberta, Edmonton, Canada, 1983.##
- [6] Aoyama and Y. Yamamoto, “A Seismic Strengthening of Existing RC Building by Steel Panel Shear Walls with Rims,”Transactions, Japan, Concrete Institute Aoyama, H., Yamamoto, Y.,1984.##
- [7] W. Tromposch and G. L. Kulak, “Cyclic and Static Behavior of Thin Panel Steel Plate Shear Walls,” Struct. Eng. Report no. 145, Dept. of Civil Eng., Univ. of Alberta, Edmonton, Canada, 1987. ##
- [8] Elgaaly, V. Caccese, and R. Chen, “Experimental Study of thin Steel –Plate Shear Walls under Cyclic Loads,” ASCE J. of Struct.Eng., vol. 119, no. 2, pp. 588-605, 1993.##
- [9] Xue and L. Lu, “Interaction of Infilled Steel Shear Wall Panels with Surrounding Frame Members,” proc. Struct. Stability Research Council Annual Technical Session, Bethlehem, Pa, pp. 320–360, 1994.##
- G. Driver, G. L. Kulak, A. E. Elwi, and D. J. L. Kennedy, “Cyclic Test of a Four-story Steel Plate Shear Wall,” ASCE J. of Struct. Eng., vol. 124, no. 2, pp. 121-130, 1998.##
- Rezai, “Seismic Behavior of Steel Plate Shear Walls by Shake Table Testing,” Phd Dissertation, Dept. of Civil Eng., Univ. of British Columbia,Vancouver, Canada, 1999.##
- Kuhn, J. P. Peterson, and L.r, Levin, “A Summary of Diagonal Tension,Part I- Methods of Analysis,” Technical Note 2661, Langley Field (VA): National Advisory Committee for Aeronautics, Langley Aeronautical Laboratory, 1952.##
- S. Lubell, H. G. L. Prion, C. E. Ventura, and M. Rezai “ Unstiffened Steel Plate Shear Wall Performance under Cyclic Load”, ASCE J. of Struct. Eng., vol. 126, no. 4, pp. 453-460, 2000.##
- FEMA 2000, “Prestandard and Commentary for the Seismic Rehabilitation of Buildings,” Report No. FEMA 356, Federal Emergency Management Agency,Washington D.C,##
- L. Kulak, D. J. L. Kennedy, R.G. Driver, and M. Medhekar, “Steel Plate Shear Walls _ an Overview,” AISC Eng. J.,38(1) , 2001.##
- Behbahanifard, R. Hussain, G. Driver, and G. Y. Grondin, “Recent Developments and Future Directions in Steel Plate Shear Wall Research,” Proc. North American Steel Construction Conf., May, Ft. Lauderdale, FL, USA, 2003.##
- Berman and M. Bruneau, “Plastic Analysis and Design of Steel Plate Shear Walls,” ASCE J. of Struct. Eng., vol. 129, no. 11, pp. 1448-1456, 2003.##
- Bruneau and d. Vian, “Testing of Special LYS Steel Plate Shear Walls,” 13th World Conf. on Earthquake Eng. Vancouver, BC , Canada, Paper No. 978, 2004.##
- H. K. Kharrazi and S. Sabouri_Ghomi, “Modified sheet-frame interaction model,” Phd. Dissertation, Univ. of British Columbia, Vancouver, BC, Canada, 2004.##
- Driver, J. Shishkin, and Y. Grondin, “Analysis of Steel Plate Shear Walls using the Modified Strip Model,” Univ. of Alberta, Dept. of Civil and Environmental Eng., 2005.##
- H. K. Kharrazi, “Rational Method for Analysis and Design of Steel Plate Shear Walls,” Phd. Dissertation, Univ. of British Columbia, Vancouver, BC, Canada, 2005.##
- Wan-Shin and Y. Hyun-Do, “Numerical Study of EarthQuake Performance of Steel Plate Shear Walls,”Dept. of Civil and Environmental Eng., Univ. of Cincinnati, 765 Baldwin Hall, Cincinnati, OH 45221, USA, 2007.##
- Sabouri_Ghomi and M. Gholhaki, “Ductility of Thin Steel Plate Shear Walls,” Asian J.of Civil Eng. (Building and Housing), Vol. 9 No. 2 pp. 150-168, 2008.##
- M. Alinia and H. R. Habashi, “Characteristics of the Wall_Frame Interaction in Steel Plate Shear Walls,” J. of Constructional Steel Research, vol. 134, no. 5, pp. 15, 2008.##
- Koppal, “Computational Investigation of Tunable Steel Plate Shear Walls for Improved Seismic Resistance,” Thesis Submitted to the Faculty of Virginia Polytechnic Institute and State Univ. Inpartial Fulfillment of the Requirements for the Degree of MSc., Dept. of Civil Eng., 2012.##
- Sabouri-Ghomi and S. R. Asad Sajjadi, “Experimental and Theoretical Studies of Steel Shear Walls with and without Stiffeners,” Civil Eng. Department, K.N. Toosi Univ., Tehran, Iran, 18 April 2012.##
- Heydari and M. Habibi, “Strengthening of Steel Plate Shear Wall,”, J. of Constructional Steel Research, 2015.
- Vafi Shahri and H. Khosravi, “Investigation of Bukling of Composite Steel Shear Wall with Smooth and Corrugated Sheets,” 2017.##
- Y., Li and X., Jinlong Pan, “Mechanical Behavior of Full-scale Composite Steel Plate Shear Wall Restrained by ECC Panels,” J. of Constructional Steel Eng, 2021,##
|