![سامانه مدیریت نشریات علمی دانشگاه امام حسین (ع)](./data/logo.png)
تعداد نشریات | 36 |
تعداد شمارهها | 1,192 |
تعداد مقالات | 8,579 |
تعداد مشاهده مقاله | 6,988,781 |
تعداد دریافت فایل اصل مقاله | 4,032,630 |
طراحی و ساخت حسگر فیبر نوری آزمایشگاهی برای اندازهگیری فشار گازها به روش فابری-پرو و بررسی تاثیر جنس پلیمری بر حساسیت آن | ||
الکترومغناطیس کاربردی | ||
مقاله 12، دوره 11، شماره 2 - شماره پیاپی 27، مهر 1402 اصل مقاله (797.81 K) | ||
نوع مقاله: مقاله پژوهشی | ||
نویسندگان | ||
علی ریاحی* 1؛ فرزاد بشیری2؛ حامد مرادی3 | ||
1دانشگاه جامع امام حسین (ع)-مرکز علم و فناوری لیزر و اپتیک | ||
2مرکز علم و فناوری لیزر و اپتیک دانشگاه جامع امام حسین (ع) | ||
3تهران-ایران | ||
تاریخ دریافت: 09 فروردین 1402، تاریخ بازنگری: 10 شهریور 1402، تاریخ پذیرش: 01 مهر 1402 | ||
چکیده | ||
در این مقاله، طراحی و ساخت حسگر فیبرنوری فابری-پرو با لایهای از مواد پلیمری پلییورتان، پیویسی نرم و پیویسی سخت با ضخامتهای یکسان 300 میکرومتر و طول کاواک 1/0 میلیمتر برای اندازهگیری فشار گاز معرفی شده و تأثیر این سه ماده پلیمری بر حساسیت حسگری فشار گاز مورد بررسی قرار گرفته است. حسگرهای فوق در دمای ثابت آزمایشگاهی تست شده و با یکدیگر مقایسه شدهاند. برای انجام تستهای فشار گاز از دو گاز اکسیژن و نیتروژن در بازه فشاری 10 تا 50 میلیبار استفاده شده است. حسگر با لایه پلییورتان برای گاز اکسیژن و نیتروژن به ترتیب دارای حساسیت 438/0 و 392/0 نانومتر بر میلیبار، حسگر با لایه پیویسی نرم برای گاز اکسیژن و نیتروژن به ترتیب دارای حساسیت 311/0 و 224/0 نانومتر بر میلیبار و حسگر با لایه پیویسی سخت برای گاز اکسیژن و نیتروژن به ترتیب دارای حساسیت 298/0 و 186/0 نانومتر بر میلیبار میباشند. نتایج بدست آمده نشان میدهد که حسگر ساخته شده با لایهنشانی پلییورتان حساسیت بیشتری نسبت به حسگرهای ساخته شده برای هر دو گاز دارد. | ||
کلیدواژهها | ||
فیبرنوری؛ حسگر فیبرنوری؛ حسگر فابری-پرو؛ فشار گاز؛ مواد پلیمری | ||
عنوان مقاله [English] | ||
Designing and manufacturing of the laboratory optical fiber sensor for detection of the gas pressure by Fabry-Perot method and the investigation of the effect of the polymer material on its sensitivity. | ||
نویسندگان [English] | ||
Ali Riahi1؛ farzad bashiri2؛ Hamed Moradi3 | ||
1Optics and laser research center, -Imam Hossein Comprehensive University University -, Tehran, Iran | ||
2optics and laser research center-imam Hossein Comprehensive University | ||
3Tehran-Iran | ||
چکیده [English] | ||
In this paper, design and fabrication of Fabry-Perot optical fiber sensors with a coating of polyurethane, Soft PVC and Rigid PVC with the same thickness of 300 μm and a cavity length of 0.1 mm was introduced for the pressure gas and the effect of these three polymeric materials on the sensitivity of gas pressure sensors was investigated. The above sensors have been tested at a constant laboratory temperature and have been compared with each other. To perform gas pressure tests, two gases of oxygen and nitrogen in the pressure range of 10 to 50mbar have been used. The sensitivity of the sensor with the coated polyurethane for oxygen and nitrogen gas is 0.438 and 0.392 nm/bar, respectively, the sensor coated with soft PVC has the sensitivity of 0.311 and 0.224 nm/bar, for oxygen and nitrogen gas respectively, and the sensors with rigid PVC coated for oxygen and nitrogen gas has the sensitivities of 0.298 and 0.186 nm/mm, respectively. The results show that the sensor made with polyurethane coating is more sensitive than the other sensors. | ||
کلیدواژهها [English] | ||
Optical Fiber, Optical Fiber Sensor, Fabry-Perot Sensor, Gas Pressure, Polymeric Materials | ||
مراجع | ||
| ||
آمار تعداد مشاهده مقاله: 3,246 تعداد دریافت فایل اصل مقاله: 1,463 |